By using this website, you agree to our use of cookies to enhance your experience.

Submit Case Report

Do you wish to submit this report?

Submit Case Report

Prior to submitting please preview the report using the Save and Preview button.

Use the browser back button to return.

Cancel Case Report Assignment

Are you sure you wish to cancel your assignment to report on this case – all inputted data will be lost!

Delete Case

Do you want to delete this case?

vet3d

Your login session has timed out.
Please login below.

Contact

Vet 3D
PO Box 6476
Coventry
CV6 9LZ

E: info@vet3d.co.uk
T: +44 (0)1676 534927

Social

This site is optimised for modern web browsers, and does not fully support your version of Internet Explorer, some sections of the website may not work correctly such as web forms

Price Guide

Please note, prices listed are exclusive of VAT and may vary depending on specific case requirements.


Precise printing costs are determined both by the intrinsic volume of the parts to be printed and their external dimensions (i.e. the volume of a box the part could fit into). Should these differ significantly from the average for the patient weight category a revised estimate of cost will be supplied before final conformation of the print order.

Default print options and common alternatives are listed, however almost anything can be printed in any resin. You can specifiy your requirements when uploading a DICOM study, or just give us a call.    

 



Developmental antebrachial deformities - osteotomy and reduction guide system

CAD-based deformity assessment and surgical planning in these cases is standardised (but can be surgeon-specified if preferred); this is included in the overall cost as well as 3D data processing, design of osteotomy and reduction guides, and 3D printing. The standard print package includes -

  • Osteotomy and reduction guides (biocompatible and autoclavable).
  • Printed pre-correction bone segment (antebrachium with elbow and carpus including base of metacarpals; autoclavable – guide fit practice).
  • Printed post-correction bone segment (as above, with reduction guide footprint; non-autoclavable – for pre-op plate contouring).

Options (price varies) include guides only, non-autoclavable pre-correction bone print, and additional post-op bone without reduction guide footprint (e.g. for second plate precontour).

 

Print

 <20kg

20-40kg

>40kg

Limb deformity - osteotomy and reduction guide system 

£705

£740

£805

 



Other limb deformities - osteotomy and reduction guide system

 

Deformity assessment and surgical planning

Please see Guide Systems - Other Deformities for more guidance.

Assessment options include -

  • Preliminary CAD assessment –
    • CAD-based overview of bone and overall limb alignment
    • E-mail review of options for more detailed assessment, surgical planning, and cost estimates
  • CAD-based deformity assessment and surgical planning -
    • Detailed CAD-based assessment of bone conformation, overall limb alignment, and surgical planning.
    • E-mail or screen-share review
  • Surgeon-specified surgical planning
    • E-mail or screen-share review following surgeon-specified deformity corrections
  • Other assessment
    • Tell us how we can help!

CAD-based deformity assessment and surgical planning can be requested as a stand-alone service - please upload DICOMs via the "Preliminary Assessment" page and specifiy this service - a cost estimate will be provided after initial assessment



Planning option

 All cases

Preliminary CAD assessment

No charge

CAD-based deformity assessment and surgical planning

£50-£250
cost dependent on CAD time required - an estimate will be provided after initial assessment

Surgeon-specified surgical planning

 No charge


Guide design and 3D-printing

Osteotomy and reduction guides are designed, with the standard print option including –

  • Pre-op bone or bone segment – to practice osteotomy guide fit (usually in autoclavable resin)
  • Post-op bone or bone segment – for plate precontouring (usually in non-autoclavable resin)
  • Osteotomy and reduction guides (autoclavable and biocompatible resin)

Options (price varies) include guides only, non-autoclavable pre-correction bone print, and additional post-op bone without reduction guide footprint (e.g. for second plate precontour).

 

Print

<20kg

20-40kg

>40kg

Other limb deformity - osteotomy and reduction guide system 

£675

£725

£785

 




 

HIF / IOHC - transcondylar screw guides

The overall cost includes 3D data processing, CAD virtual screw trajectory planning and guide design, and 3D printing. There are two standard print packages -

  1. Single drill guide
    • Usually for 2.5mm drill bit (other sizes can be specified) - requires manual overdrilling of this pilot hole to desired final diameter.
    • 3D print of condyle with pilot hole (autoclavable resin).
  2. Sequential drill guides
    • Three sequential guides, usually starting at 2.5mm with intermediate and largest sizes to suit planned implant
    • 3D print of condyle with pilot hole (autoclavable resin).

Options (reduced cost) include guide / guides only, and non-autoclavable condyle print.
   

Print

 <20kg

20-40kg

>40kg

Transcondylar screw guide - single 

£230

£250

£270

Transcondylar screw guides - 3 sequential

£345

£370

£400





3D bone prints

The overall cost includes 3D data processing and 3D printing. Bones are printed in white, non-autoclavable resin, although options include biocompatible & autoclavable resin, autoclavable resin, and clear resin (non-autoclavable) - prices vary please ask.

Standard models are listed below, although ultimately any bone or limb segment can be printed as specified.

  • Single bone print - e.g. a long bone, a joint, or up to three vertebrae.
  • Limb segment - e.g. antebrachium including elbow and carpus, antebrachium including paw, longer vertebral segment, other specified limb section.
  • Whole limb / complex bone print. Please note these prints can be considerably more expensive than single bones or segments due their greater volume which can complicate printing.

Although guide prices are given below these projects vary considerably in degree of data processing required and print costs - please call for a rough estimate or submit DICOMs for a more accurate estimate.

  

Print

 <20kg

20-40kg

>40kg

Single bone

 

£90

£110

£150

Single bone - duplicate

£75

£95

£135

Limb segment

£120

£180

£220

Complex bone

£200

£280

£450

 


 

Distal Femoral Osteotomy - osteotomy and reduction guide system

The overall cost includes 3D data processing, CAD virtual osteotomy planning and design of osteotomy and reduction guides, and 3D printing.

If required CAD-based quantification of femoral varus and torsion is also included in the total cost, or these values can be surgeon-specified.

  • Please note should this be requested and DFO prove not to be indicated a fee of £55 will be invoiced to cover data processing and CAD time.
  • CAD-based quantification of femoral varus and torsion can be requested as a stand-alone service for the same fee - please upload DICOMs via the "Preliminary Assessment" page and specifiy this service.

The standard print package includes -

  • Osteotomy and reduction guides (biocompatible and autoclavable)
  • Printed pre-correction distal femur (autoclavable – guide fit practice)
  • Printed post-correction distal femur with reduction guide footprint (non-autoclavable – for pre-op plate contouring)

Options (price varies) include guides only, non-autoclavable pre-correction bone print, and additional post-op bone without reduction guide footprint (e.g. for second plate precontour).
  
   

Print

<20kg 

20-40kg

>40kg

DFO - osteotomy and reduction guide system

£600

£645

£710

 

 


 

Fracture reduction guide system

The reduction guide system can be used for either traditional open reduction and internal fixation (ORIF) or minimally invasive plate osteosynthesis (MIPO).

The overall cost includes 3D data processing, CAD virtual reduction planning and design of Ellis pin orientation and reduction guides, and 3D printing. The standard print package includes -

  • Ellis pin orientation guides and reduction guide
  • Printed major fracture fragments – guide fit practice
  • Printed post-reduction bone with reduction guide footprint

Due to time-constraints all prints are usually in autoclavable, biocompatible resin.

In most cases CAD design and printing are done on the day of receipt and are posted the following day (special delivery by 9am).

Please contact us by phone to check availability of overnight design / print service and to confirm your requirements.

 

Print

 <20kg

20-40kg

>40kg

Fracture reduction guide system - ORIF 

£750

£775

£825

Fracture reduction guide system- MIPO

£800

£825

£900

 



 

Vertebral pedicle screw drill guides

The overall cost includes 3D data processing, CAD virtual screw trajectory planning and guide design, and 3D printing. The standard print package includes -

  • Vertebral drill guides (biocompatible and autoclavable)
  • Printed vertebrae with screw holes (autoclavable – guide fit practice and for screw length measurement).


   

Print

 

20-40kg

>40kg

Vertebral drill guides - 2 vertebrae 

£640

£670

£720

Each additional vertebra 

£120

£130

£140

 

©Copyright 2017 - Vet 3D | Terms & Conditions | Cookie Policy